How to replace and re-cut a plastic backflash
Re: New Bryans Backflash ball release hole
I would not advocate gluing the flash for one very good reason. The solvents in most glues will dissolve either the backing layer and possibly the colour layer. I would follow pennymachines' advice. I used a sharp flat wood bit to cut the hole on a very slow drill, having tried a hole punch, which simply split the plastic.
fit new backflash etc etc
Topic merged - Site Admin.
Hi all,
I'm attempting to make one decent machine (Whales - Win a Kit-Kat) from a complete door and a "butchered" complete machine.
I guess I have all the bits to finish-up with one complete machine but WHERE TO START!
I am currently working on a new backflash, but how do I position it on the existing fixing holes and what is the best method of cutting the holes for ball release/gallery.
Any advice will be much appreciated and let me know if anyone needs the file of the backflash when it's done.
Thanks in advance. M_ick
Hi all,
I'm attempting to make one decent machine (Whales - Win a Kit-Kat) from a complete door and a "butchered" complete machine.
I guess I have all the bits to finish-up with one complete machine but WHERE TO START!
I am currently working on a new backflash, but how do I position it on the existing fixing holes and what is the best method of cutting the holes for ball release/gallery.
Any advice will be much appreciated and let me know if anyone needs the file of the backflash when it's done.
Thanks in advance. M_ick
- badpenny
- Forum Moderator
- Posts: 7221
- Joined: Thu May 05, 2005 12:41 pm
- Reaction score: 28
- Location: East Midlands
Re: fit new backflash etc etc
Coincidently we were talking about this very thing less than a month ago .... (now merged above - Site Admin.)
BP
BP
Re: fit new backflash etc etc
I like to use a dremel style sanding wheel to smooth out the allwin ball entry/release holes. Either used in a Dremel or just in a standard hand drill. The sanding wheels are slightly smaller than what's needed so after drilling a pilot hole from the back of the artwork you can clean up and make sure there is no lip. Looks pro.
-
- Site Admin
- Posts: 6650
- Joined: Wed Nov 06, 2002 12:12 am
- Reaction score: 59
- Location: The Black Country
Re: fit new backflash etc etc
Assuming you're starting with clear plastic - hold it in place while you mark up the holes with a non-permanent marker pen. Otherwise, use a piece of tracing paper.m_ick wrote:how do I position it on the existing fixing holes
I'm sure it will prove useful if you upload it to Resources.m_ick wrote:let me know if anyone needs the file of the backflash when it's done.
B M Co. backflash help
Topic moved & merged - Site Admin.
Hi everyone I'm currently restoring a large case B M Co. 24 cup allwin. I need a new backflash. It's red and a thinnish plastic like material but I don't know where I could get one from. I have brought some red card close to the colour and was going to have a play with getting one laminated and one sprayed with clear lacquer as a trial and error. I hope someone can help and give some advise please
Regards Dave.
Hi everyone I'm currently restoring a large case B M Co. 24 cup allwin. I need a new backflash. It's red and a thinnish plastic like material but I don't know where I could get one from. I have brought some red card close to the colour and was going to have a play with getting one laminated and one sprayed with clear lacquer as a trial and error. I hope someone can help and give some advise please
Regards Dave.
- badpenny
- Forum Moderator
- Posts: 7221
- Joined: Thu May 05, 2005 12:41 pm
- Reaction score: 28
- Location: East Midlands
Re: B m & co backflash help
Hi Dave, have you tried searching "backflash" or "back flash" in the Resources section of the forum?
Re: B m & co backflash help
I haven't done yet as I'm relatively new so getting used to how it all works, will have a look now thanks
- badpenny
- Forum Moderator
- Posts: 7221
- Joined: Thu May 05, 2005 12:41 pm
- Reaction score: 28
- Location: East Midlands
Re: B m & co backflash help
I'm not promising you'll find what you need, I know there a few in there but I don't go out of my way for allwins.
You might need someone who is into BMCo and can photo one.
But it's worth a look.
You might need someone who is into BMCo and can photo one.
But it's worth a look.
Re: B m & co backflash help
Best place I know for thinnish coloured plastic is Fred Aldous of Manchester. I bought a yellow and red A1 sheet for around a fiver each last year and delivery was excellent. Give it a go although you may not get the exact match but I was well pleased and have enough over to replace another backflash should another restoration project come my way.
http://www.fredaldous.co.uk/
http://www.fredaldous.co.uk/
Re: B m & co backflash help
Thanks for the help GM. I'll take a look as that. It sounds like what I need! How did you successfully cut out the holes for the cups etc?
Re: B m & co backflash help
To cut the holes I've always used a proper surgical scalpel which I find far better than these craft knives. Mine is made by Swann Morton and uses 10A blades. You'll find them via Google and they are very sharp. The good thing about this material is that it's thin enough to shine a torch through which makes cutting the holes easier and a small file smooths the edges for a good job. Main thing is, take your time !
My friend told me to send you this link to Fred Aldous which I used for a yellow sheet but you've probably already found it by now ! Good Luck .
http://www.fredaldous.co.uk/poly-prop-s ... ellow.html
My friend told me to send you this link to Fred Aldous which I used for a yellow sheet but you've probably already found it by now ! Good Luck .
http://www.fredaldous.co.uk/poly-prop-s ... ellow.html
Who is online
Users browsing this forum: No registered users and 8 guests