Flatten a plastic backflash

Advice and guidance on repair and restoration techniques.
User avatar
scottie
Posts: 284
Joined: Fri Oct 30, 2009 1:10 pm
Location: Canada

Flatten a plastic backflash

Post by scottie »

This Win-a-Gift top flash was very warped when I took it off the machine.
I put it between a wet piece of cotton towel, then I used a hot iron and pushed down hard and ironed it for a few minutes. I took the still warm top flash, wrapped a paper towel around it, and put ii under the weight of the cabinet of the game. The next morning it was straight and very flat .....worked great.
scottie
Attachments
WIN-A-GIFT.jpg
WIN-A-GIFT.jpg (3.96 KiB) Viewed 1618 times
junior
Posts: 177
Joined: Sat Sep 20, 2014 7:33 pm

Flatten a plastic backflash

Post by junior »

Topic merged - Site Admin.

I have a Fireworks. To cover the hammer there is a decorative piece of plastic on the front of the box held by two screws. Over many years of existence the plastic has twisted and cracked so badly the hammer won't work. The only answer I could come up with was to place it on a baking tray in an electric oven on low and heat it up and gradually try to flatten it. It took about 10 minutes in and out and it has eased itself back into a respectable shape, helped by some thumb pressure. So far so good. Hope this helps someone in future. Now you can't learn that from Sainsbury's or Tesco. :D
User avatar
badpenny
Forum Moderator
Posts: 6642
Joined: Thu May 05, 2005 12:41 pm
Location: East Midlands

Re: Flatten a plastic backflash

Post by badpenny »

Good tip that.
Although I believe Waitrose covered it in August :lol:

I believe it has/should have a bulb behind it? So perhaps that helped its distortion?
User avatar
scottie
Posts: 284
Joined: Fri Oct 30, 2009 1:10 pm
Location: Canada

Re: Flatten a plastic backflash

Post by scottie »

Hi Junior
You could try a hot iron with a damp towel. I did this on a top flash and then after I was finished I put the top flash under a heavy flat surface to cool off and it worked great. I'm sure it would work on the backflash, just being bigger it would take a bit more time.
Scottie
liquorbox
Posts: 75
Joined: Wed Jan 24, 2018 8:54 pm

Re: Flatten a plastic backflash

Post by liquorbox »

A cheap heat gun will give heat only to where you need it.
I use one to make birds out of plastic piping and it works well !!CHEERS!!
junior
Posts: 177
Joined: Sat Sep 20, 2014 7:33 pm

Re: Flatten a plastic backflash

Post by junior »

Thanks for replies. The plastic is only 3 x 2 inches in size so I wanted to heat the whole of it evenly to get flexibility as it had twisted both ways and had a crack in it. I considered using a heat gun but thought it would be too intense. This piece of plastic has a picture on it and I wasn't sure if it would melt. Done enough, looks OK and hammer works.
User avatar
gameswat
Posts: 1973
Joined: Sat May 30, 2009 5:17 am
Location: perth, australia

Re: Flatten a plastic backflash

Post by gameswat »

JR, old plastic that's been bent & re-flattened has a habit of returning, so after years of messing with this (vintage pins especially) I usually now end up covering the restored originals with thin but tough polycarb clear which does wonders in stopping the process. And the added bonus of UV protection.
greg
Posts: 57
Joined: Sun Feb 10, 2013 6:44 pm
Location: North Carolina, USA

Flatten a plastic backflash

Post by greg »

Topic copied, edited and merged from Flatten OW backflash & unidentified tin - Site Admin.

If someone has come up with an innovative new way to flatten the plastic playfield I would love to hear about it. This poor game is unplayable until I find a way to flatten the playfield over the winning holes.
Attachments
DSC01512a.jpg
User avatar
treefrog
Posts: 4114
Joined: Mon Sep 29, 2008 2:46 pm
Location: Suffolk

Re: Flatten a plastic backflash

Post by treefrog »

Search the site as many have made attempts at flattening these backflashes, from removing backflash and placing between two sheets and gently applying heat from say a hair dryer, to another member who put his in an oven. I have stopped buying Olly Whales machines and sold all mine last year as not such a fan of this flaw.
greg
Posts: 57
Joined: Sun Feb 10, 2013 6:44 pm
Location: North Carolina, USA

Re: Flatten plastic

Post by greg »


DSC01512b.jpg

I have tried flattening a play field with the gentle application of heat from a heat gun with not much luck. I even tried laying a piece of glass over it to distribute the heat evenly. The glass shattered.

The oven scares me. With the heat gun I only screw up one small area at a time. With the oven I can destroy the entire thing in one shot. I'm sure someone has a "Double Secret" way to flatten play fields they have never shared....it's time to share your secret with the world and the world will love you for it!
Post Reply

Who is online

Users browsing this forum: No registered users and 2 guests