Somebody knows... Maybe you?
User avatar
coppinpr
Posts: 4088
Joined: Sun Oct 10, 2010 2:01 pm
Location: Lewes, East Sussex
Contact:

Re: Duomat penny slot machine

Postby coppinpr » Wed Dec 07, 2016 8:55 am

I'm searching on my computer for the sticker kit, but as yet it's lost in the maze. It was some years ago. I'll find it, give me time. Do not remove the old ones as yet, I may need the measurements to create a new set for you later.

The problem with the back door is... it's not a back door, it's a half cabinet about the same size as the front half (see one of my photos earlier). Even with the back half they tend to fall over when you work on them. Best way by far is to remove the mech which comes out in one piece very easy (I think 3 wing nuts and a couple of cir-clips and it's out). Then you can work on the case easy and the mech easy as it stands up nicely on its own.

User avatar
mei-mei
Posts: 221
Joined: Sat Dec 03, 2016 8:41 am

Re: Duomat penny slot machine

Postby mei-mei » Wed Dec 07, 2016 9:14 am

Thanks, helpful. Still need the other half (door) though or the mech might get damages with use.

User avatar
badpenny
Forum Moderator
Posts: 6384
Joined: Thu May 05, 2005 12:41 pm
Location: East Midlands
Contact:

Re: Duomat penny slot machine

Postby badpenny » Wed Dec 07, 2016 10:01 am

I may have the frame for the back bit, probably tatty as hell, but it's a start.

BP

User avatar
mei-mei
Posts: 221
Joined: Sat Dec 03, 2016 8:41 am

Re: Duomat penny slot machine

Postby mei-mei » Wed Dec 07, 2016 11:40 am

BP you are a life saver! I can deal with the cosmetics not a prob. How do we proceed? Mei-mei

User avatar
mei-mei
Posts: 221
Joined: Sat Dec 03, 2016 8:41 am

Re: Duomat penny slot machine

Postby mei-mei » Wed Dec 07, 2016 11:55 am

P.S. BP, I have attached a pic of the mech attached to the handle at bottom of the machine. It would seem it is missing a part where the rod attaches. Might you also have one of these?
back-1-(2)a.jpg
back-1-(2)a.jpg (9.97 KiB) Viewed 1263 times

User avatar
coppinpr
Posts: 4088
Joined: Sun Oct 10, 2010 2:01 pm
Location: Lewes, East Sussex
Contact:

Re: Duomat penny slot machine

Postby coppinpr » Wed Dec 07, 2016 12:48 pm

How do we proceed?
1st thing is you have to laugh at BP's jokes. It's not easy but pays dividends !!THUMBSX2!!

User avatar
mei-mei
Posts: 221
Joined: Sat Dec 03, 2016 8:41 am

Re: Duomat penny slot machine

Postby mei-mei » Wed Dec 07, 2016 1:12 pm

Wow you wanna make this really hard. Ok, he he he he he !WORSHIPFULL!

User avatar
badpenny
Forum Moderator
Posts: 6384
Joined: Thu May 05, 2005 12:41 pm
Location: East Midlands
Contact:

Re: Duomat penny slot machine

Postby badpenny » Wed Dec 07, 2016 1:53 pm

mei-mei wrote:P.S. BP, I have attached a pic of the mech attached to the handle at bottom of the machine. It would seem it is missing a part where the rod attaches. Might you also have one of these?
This really is your lucky day!
I'm aiming to collect all my babies Sun 18th December. :cool:

User avatar
mei-mei
Posts: 221
Joined: Sat Dec 03, 2016 8:41 am

Re: Duomat penny slot machine

Postby mei-mei » Wed Dec 07, 2016 2:09 pm

All hail BP all hail BP!!!!! !!YIPPEE!!

User avatar
badpenny
Forum Moderator
Posts: 6384
Joined: Thu May 05, 2005 12:41 pm
Location: East Midlands
Contact:

Re: Duomat penny slot machine

Postby badpenny » Mon Dec 19, 2016 9:03 pm

I was running out of room in the truck, so didn't get to load all of my machines, but remembered to dig out the "gash" Duomat.
Turns out it has 3 sides of the front case but none of the rear part - sorry
The mech is lacking payout tubes, slides and clock - but I seem to recall you're ok on that front.

I think it's the handle and gubbins you need.

Look at the photos and have a think.
mech from side.jpg
handle mech.jpg
front of mech.jpg


Who is online

Users browsing this forum: No registered users and 14 guests