How to replace and re-cut a plastic backflash
Re: Wonders allwin back plastic
I was advised by a member of this site to do it in the following manner, which is what I did. Get a piece of 15mm copper pipe about 6 inches long; hold the end over a flame to heat it (in my case I used the gas hob on the cooker); holding the other end of the pipe with a rag or similar around it as it gets hot; then, having secured the acetate sheet on the backboard, pierce the acetate with the heated pipe through the holes. I would imagine whatever method is chosen it can get a bit tedious but worth it in the end. I used a panel pin to make the screw holes.
Re: Wonders allwin back plastic
Perfect!
Looks so much better and it works now, which is a big bonus. Quite easy to do once you start - leather punch kit is man's best friend.
Thanks to everyone who helped.
Looks so much better and it works now, which is a big bonus. Quite easy to do once you start - leather punch kit is man's best friend.
Thanks to everyone who helped.
Re: Wonders allwin back plastic
Too right Stu.
It's amazing how much dirt there was under that old plastic and how clean it came with a bit careful cleaning.
It's amazing how much dirt there was under that old plastic and how clean it came with a bit careful cleaning.
Re: allwin plastic backflash for defiant
Topic merged - Site Admin.
Does anyone know where I can get some plastic sheeting that would be suitable for cutting and making a new backflash for a Defiant allwin?
This sort of stuff:
Thanks.
Does anyone know where I can get some plastic sheeting that would be suitable for cutting and making a new backflash for a Defiant allwin?
This sort of stuff:
Thanks.
-
- Site Admin
- Posts: 6650
- Joined: Wed Nov 06, 2002 12:12 am
- Reaction score: 59
- Location: The Black Country
Re: allwin plastic backflash for defiant
pennymachines wrote:You can buy coloured acrylic sheets from craft stores and various online shops. I buy UV-protected clear plastic off a roll at a garden centre (for making cloches etc.). You can then back-paint it to the exact colour/colours required.
Cutting holes in backflash
Topic merged - Site Admin.
I am finally getting around to putting a new backflash on my Bryans Fivewin.
As you only get one chance at making the ball release hole in the backflash, before making a mess of it, can anyone recommend a tried and tested way of getting the best result.
I intend firstly to glue the backlash in place, then when dry to cut the holes.
Any advice out there greatly accepted.
I am finally getting around to putting a new backflash on my Bryans Fivewin.
As you only get one chance at making the ball release hole in the backflash, before making a mess of it, can anyone recommend a tried and tested way of getting the best result.
I intend firstly to glue the backlash in place, then when dry to cut the holes.
Any advice out there greatly accepted.
- badpenny
- Forum Moderator
- Posts: 7221
- Joined: Thu May 05, 2005 12:41 pm
- Reaction score: 28
- Location: East Midlands
Re: New Bryans Backflash ball release hole
Put a light behind it to locate it and use a pin to pierce through the outline.
Tidy up with a hobby knife.
Tidy up with a hobby knife.
-
- Site Admin
- Posts: 6650
- Joined: Wed Nov 06, 2002 12:12 am
- Reaction score: 59
- Location: The Black Country
Re: New Bryans Backflash ball release hole
I'm not sure why you want to glue the backflash. The fittings should hold it in place perfectly adequately. Bowing and warping of old plastic flashes was caused by expansion, particularly when machines were operated outside in direct sunlight. Had they been glued, I think the plastic would still have moved, tearing off the underside graphics.
Re: New Bryans Backflash ball release hole
I would not advocate gluing the flash for one very good reason. The solvents in most glues will dissolve either the backing layer and possibly the colour layer. I would follow pennymachines' advice. I used a sharp flat wood bit to cut the hole on a very slow drill, having tried a hole punch, which simply split the plastic.
fit new backflash etc etc
Topic merged - Site Admin.
Hi all,
I'm attempting to make one decent machine (Whales - Win a Kit-Kat) from a complete door and a "butchered" complete machine.
I guess I have all the bits to finish-up with one complete machine but WHERE TO START!
I am currently working on a new backflash, but how do I position it on the existing fixing holes and what is the best method of cutting the holes for ball release/gallery.
Any advice will be much appreciated and let me know if anyone needs the file of the backflash when it's done.
Thanks in advance. M_ick
Hi all,
I'm attempting to make one decent machine (Whales - Win a Kit-Kat) from a complete door and a "butchered" complete machine.
I guess I have all the bits to finish-up with one complete machine but WHERE TO START!
I am currently working on a new backflash, but how do I position it on the existing fixing holes and what is the best method of cutting the holes for ball release/gallery.
Any advice will be much appreciated and let me know if anyone needs the file of the backflash when it's done.
Thanks in advance. M_ick
- badpenny
- Forum Moderator
- Posts: 7221
- Joined: Thu May 05, 2005 12:41 pm
- Reaction score: 28
- Location: East Midlands
Re: fit new backflash etc etc
Coincidently we were talking about this very thing less than a month ago .... (now merged above - Site Admin.)
BP
BP
Re: fit new backflash etc etc
I like to use a dremel style sanding wheel to smooth out the allwin ball entry/release holes. Either used in a Dremel or just in a standard hand drill. The sanding wheels are slightly smaller than what's needed so after drilling a pilot hole from the back of the artwork you can clean up and make sure there is no lip. Looks pro.
-
- Site Admin
- Posts: 6650
- Joined: Wed Nov 06, 2002 12:12 am
- Reaction score: 59
- Location: The Black Country
Re: fit new backflash etc etc
Assuming you're starting with clear plastic - hold it in place while you mark up the holes with a non-permanent marker pen. Otherwise, use a piece of tracing paper.m_ick wrote:how do I position it on the existing fixing holes
I'm sure it will prove useful if you upload it to Resources.m_ick wrote:let me know if anyone needs the file of the backflash when it's done.
B M Co. backflash help
Topic moved & merged - Site Admin.
Hi everyone I'm currently restoring a large case B M Co. 24 cup allwin. I need a new backflash. It's red and a thinnish plastic like material but I don't know where I could get one from. I have brought some red card close to the colour and was going to have a play with getting one laminated and one sprayed with clear lacquer as a trial and error. I hope someone can help and give some advise please
Regards Dave.
Hi everyone I'm currently restoring a large case B M Co. 24 cup allwin. I need a new backflash. It's red and a thinnish plastic like material but I don't know where I could get one from. I have brought some red card close to the colour and was going to have a play with getting one laminated and one sprayed with clear lacquer as a trial and error. I hope someone can help and give some advise please
Regards Dave.
- badpenny
- Forum Moderator
- Posts: 7221
- Joined: Thu May 05, 2005 12:41 pm
- Reaction score: 28
- Location: East Midlands
Re: B m & co backflash help
Hi Dave, have you tried searching "backflash" or "back flash" in the Resources section of the forum?
Re: B m & co backflash help
I haven't done yet as I'm relatively new so getting used to how it all works, will have a look now thanks
- badpenny
- Forum Moderator
- Posts: 7221
- Joined: Thu May 05, 2005 12:41 pm
- Reaction score: 28
- Location: East Midlands
Re: B m & co backflash help
I'm not promising you'll find what you need, I know there a few in there but I don't go out of my way for allwins.
You might need someone who is into BMCo and can photo one.
But it's worth a look.
You might need someone who is into BMCo and can photo one.
But it's worth a look.
Who is online
Users browsing this forum: No registered users and 16 guests