General vintage slot machine related topics.
simondiwell
Posts: 4
Joined: Mon Jul 30, 2018 10:50 am

Ruffler and Walker Earth Satellite repair help

Postby simondiwell » Tue Aug 07, 2018 8:50 pm

Hi there,

I'm tying to restore an Earth Satellite machine. My one is in quite a sorry state and the ball cups/ tubes are missing, so I am going to try to make these parts from scratch. I was wondering if anyone has one and could take a photo of the inside part of the ball cups/ tubes mechanism if possible please so I can base what I make on that? Also could anyone tell me what ball size the machine uses?

I am new to this and trying to figure out how to get it working.

Any help would be much appreciated.

Regards

Simon

User avatar
badpenny
Forum Moderator
Posts: 5955
Joined: Thu May 05, 2005 12:41 pm
Location: East Midlands
Contact:

Re: Ruffler and walker earth satellite repair help

Postby badpenny » Tue Aug 07, 2018 10:04 pm

Strewth! ……. Well done you and welcome to the forum.

I recently restored one, then sold it on.
The tubes are also the cups. The ends of the tubes protrude through the play field to catch the ball.

Each tube has a hole part way down its length to drop the ball into the correct gulley which runs at right angle to it. That leads it to the wedge shaped contraption that gauges where the feeler probe ends up and how many of the slides it shoves.
The tubes are held in place by a spring loaded bar that clamps down on the tube ends that don't poke through the holes.

Apart from that I'm useless, sorry.

BP :cool:

User avatar
bryans fan
Posts: 564
Joined: Mon Feb 03, 2003 10:15 pm
Location: Somerset

Re: Ruffler and Walker Earth Satellite repair help

Postby bryans fan » Wed Aug 08, 2018 9:07 am

Found this picture, which may or may not be of help. :!?!:



earth satelite mech.jpg

simondiwell
Posts: 4
Joined: Mon Jul 30, 2018 10:50 am

Re: Ruffler and Walker Earth Satellite repair help

Postby simondiwell » Wed Aug 08, 2018 9:51 am

Thanks so much for both replies! Unbelievably helpful and should be enough for me to be able to make some thing similar. With regards to ball size, would it be just trial and error? I've tried a 1/2inch ball which is too small to trigger the mechanisms and one that is 9/16 inch which seems to be too big and getting stuck in the pins and holes. There's not much room in between those sizes.. I don't want to start adjusting stuff until I know I've got the right size ball in. So thought I'd just ask.

Cheers,

Simon

User avatar
treefrog
Posts: 3279
Joined: Mon Sep 29, 2008 2:46 pm
Location: Suffolk

Re: Ruffler and Walker Earth Satellite repair help

Postby treefrog » Wed Aug 08, 2018 10:14 am

You might want to read below thread where 14mm was found better than 9/16 being slightly smaller

Fill 'Em Up, Many Happy Returns - ball sizes please?

User avatar
gameswat
Posts: 1702
Joined: Sat May 30, 2009 5:17 am
Location: perth, australia

Re: Ruffler and Walker Earth Satellite repair help

Postby gameswat » Wed Aug 08, 2018 12:14 pm

Something as yet unmentioned is that these games came with 8 x spare tubes for customizing the games. Very simple and clever idea really. Though trying to get an owner to sell you their spares might be troublesome? And not quite enough to fill your game. Hopefully these photos help.
earth satellite mech 1.jpg
earth satellite mech 7.jpg
earth satellite mech 6.jpg
earth satellite mech 5.jpg
earth satellite mech 4.jpg
earth satellite mech 2.jpg
earth satellite mech 3.jpg

User avatar
gameswat
Posts: 1702
Joined: Sat May 30, 2009 5:17 am
Location: perth, australia

Re: Ruffler and Walker Earth Satellite repair help

Postby gameswat » Wed Aug 08, 2018 1:35 pm

OK, thought about it and figured this would make your life pretty damn easy. Laid masking tape over the outside of an original tube and cut it out. Then added the holes for the other tubes, and the four side folds. So this is now a generic pattern you can print out and use for making any of the tubes. It was scanned so should still be life size, but just in case I added the sizes it should be once printed. I usually just print out my patterns on paper and then spray glue on the back of that and onto the sheet of alloy (or brass etc) and then cut and file it out.
r and w tube pattern.jpg

simondiwell
Posts: 4
Joined: Mon Jul 30, 2018 10:50 am

Re: Ruffler and Walker Earth Satellite repair help

Postby simondiwell » Wed Aug 08, 2018 9:52 pm

Oh wow thank you so much for the replies!

User avatar
badpenny
Forum Moderator
Posts: 5955
Joined: Thu May 05, 2005 12:41 pm
Location: East Midlands
Contact:

Re: Ruffler and Walker Earth Satellite repair help

Postby badpenny » Thu Aug 09, 2018 12:23 am

That's a superb piece of work there Gameswat.

This website really delivers.
BP :cool:

User avatar
john t peterson
Posts: 978
Joined: Wed Dec 01, 2004 5:40 pm
Location: USA
Contact:

Re: Ruffler and Walker Earth Satellite repair help

Postby john t peterson » Thu Aug 09, 2018 8:13 pm

Gameswat,

I've decided to develop a flying car. As you are well aware, I have no mechanical talent nor inspiration. Please have your plans for my car on my desk in one week.

J Peterson
Flying blind in USA. !!PLANE!!


Who is online

Users browsing this forum: No registered users and 1 guest