Re-introduction and a Bryan's question
Re-introduction and a Bryan's question
Hi all,
Although I've been a member here since 2011, I haven't been active since then because of life getting in the way as it so often does - and I had to sell two of my four penny machines back then to raise funds for roof work on the house too. So this is to just say "re-hello" and I hope this time I will be able to enjoy the hobby a bit more than I did a few years back!
Anyway - I did hang on to a couple (Bullion and Bell-Fruit Cascade), and have now just got myself a third after all that time - nothing rare but a good old Elevenses.
My question is: someone's converted it from a 1P to a 1D machine - coin tray, vertical slide and coin entry are all correct for 1D. But the top coin chute part (pictured below) is still 1P and has been made to work just by strategic removal of two of the small nuts and bolts and a bit of gaffer tape added... which is far from ideal.
Although looking for a 1D replacement ideally, if I made my own, what metal should I be looking to get for a) the sheet sides and b) the square sections which form the front and prevent the coin falling out?
I've been looking at Zintec sheet steel (zinc coated) 0.9mm - too thick?
Cheers!
Although I've been a member here since 2011, I haven't been active since then because of life getting in the way as it so often does - and I had to sell two of my four penny machines back then to raise funds for roof work on the house too. So this is to just say "re-hello" and I hope this time I will be able to enjoy the hobby a bit more than I did a few years back!
Anyway - I did hang on to a couple (Bullion and Bell-Fruit Cascade), and have now just got myself a third after all that time - nothing rare but a good old Elevenses.
My question is: someone's converted it from a 1P to a 1D machine - coin tray, vertical slide and coin entry are all correct for 1D. But the top coin chute part (pictured below) is still 1P and has been made to work just by strategic removal of two of the small nuts and bolts and a bit of gaffer tape added... which is far from ideal.
Although looking for a 1D replacement ideally, if I made my own, what metal should I be looking to get for a) the sheet sides and b) the square sections which form the front and prevent the coin falling out?
I've been looking at Zintec sheet steel (zinc coated) 0.9mm - too thick?
Cheers!
- bryansjim
- Posts: 45
- Joined: Fri Dec 03, 2004 6:34 pm
- Reaction score: 0
- Location: Mirfield West Yorkshire
Re: Re-introduction and a Bryan's question
I made a few of these years ago. I will have a look in the garage when I get a minute.
Re: Re-introduction and a Bryan's question
That would be fantastic if you did still have one lurking.
And if not, maybe an idea of if the zintec stuff is going to be ok to use, or if not, what's best.
Thanks
And if not, maybe an idea of if the zintec stuff is going to be ok to use, or if not, what's best.
Thanks
Re: Re-introduction and a Bryan's question
Brass was the material I used for the same part on a half-crown change machine.
It has the advantage of taking solder readily, which avoids the bolt-heads which sometimes interfere with reliable working of coin-chutes.
It has the advantage of taking solder readily, which avoids the bolt-heads which sometimes interfere with reliable working of coin-chutes.
Re: Re-introduction and a Bryan's question
Thanks - an interesting thought - have never soldered anything before but there's one way to learn...
I'll see if Bryansjim or my Wanted advert come up with anything first though.
- bryansjim
- Posts: 45
- Joined: Fri Dec 03, 2004 6:34 pm
- Reaction score: 0
- Location: Mirfield West Yorkshire
Re: Re-introduction and a Bryan's question
The ones I made were made from zintex and tack welded I think.
- bryansjim
- Posts: 45
- Joined: Fri Dec 03, 2004 6:34 pm
- Reaction score: 0
- Location: Mirfield West Yorkshire
Re: Re-introduction and a Bryan's question
Just had a root through box after box of stuff, I really must sell some on.
Don't have any, I could make up a batch.
Don't have any, I could make up a batch.
Re: Re-introduction and a Bryan's question
That looks good - a different design to mine in terms of the proportion of vertical open chute being shorter on mine with the 'top part' having an extended drop before the join to the vertical.
Have not heard from anyone yet regarding my wanted advert (you'd think there'd be parts of Bryan's Allwins lurking in all sorts of places) but am still hopeful, however if nothing then a decent new part would be very welcome!
Have not heard from anyone yet regarding my wanted advert (you'd think there'd be parts of Bryan's Allwins lurking in all sorts of places) but am still hopeful, however if nothing then a decent new part would be very welcome!
Who is online
Users browsing this forum: No registered users and 11 guests