Mills "Wizard" alloy corrosion removal
- gameswat
- Posts: 2220
- Joined: Sat May 30, 2009 5:17 am
- Reactions score: 40
- Location: perth, australia
Mills "Wizard" alloy corrosion removal
I know you all loathe a good before and after, but whatever..... worst alloy corrosion I've had to restore. Picked this up in the US weeks ago for a very bargain price because it looked so bad. About 5 hrs going slowly with a rust convertor (basically oxalic acid) and fine wire brushes. I prefer to go slow so as to document, or hopefully save the original paint. In this case the corrosion was under nearly all the paint so everything had to come off. And there were very small differences in the paint to the other one of these I did. Then to remove the final deep pitting I soaked in a bath of an alloy corrosion remover mixed with hot water for several hours, as sold here in auto stores for cleaning alloy bumper bars and rims etc. I also lightly sanded down some of the bad high points to remove much surface pitting. Obviously once painted the background will be mostly hidden. Very happy with the outcome. Once re-painted will come up close to this other one I did.
Re: Mills "Wizard" alloy corrosion removal
Very good , although a small amount of the detailed artwork has been lost or damaged, because it is such a busy casting you're unlikely to notice.... On anything plain it is much more difficult to hide, especially when corrosion goes deep from my experience......
What are those strange figures on the right, looks like two babies facing each other, strange?
What are those strange figures on the right, looks like two babies facing each other, strange?
- gameswat
- Posts: 2220
- Joined: Sat May 30, 2009 5:17 am
- Reactions score: 40
- Location: perth, australia
Re: Mills "Wizard" alloy corrosion removal
Oops, thought you meant the two birds in the middle, in fact those are the astrological signs running down the rhd side, the twins being Gemini, it is a fortune machine after all.
- john t peterson
- Posts: 1354
- Joined: Wed Dec 01, 2004 5:40 pm
- Reactions score: 14
- Location: USA
Re: Mills "Wizard" alloy corrosion removal
Gameswat,
I have some corrosion on my 1972 Ford Pinto I'd like you to address. When you have time, of course.
J Peterson
American Pony Man
I have some corrosion on my 1972 Ford Pinto I'd like you to address. When you have time, of course.
J Peterson
American Pony Man
- radiochrissie
- Posts: 212
- Joined: Sun Oct 10, 2010 7:03 pm
- Reactions score: 0
- Location: The Iron Men
Re: Mills "Wizard" alloy corrosion removal
The time , effort and expertise really pays off. Another wonderful restoration.
I see you live in Perth, my daughter is in Cockburn, it’s a fine place to live.
I see you live in Perth, my daughter is in Cockburn, it’s a fine place to live.
- watlingman
- Posts: 93
- Joined: Sun Jul 15, 2018 5:44 pm
- Reactions score: 3
- gameswat
- Posts: 2220
- Joined: Sat May 30, 2009 5:17 am
- Reactions score: 40
- Location: perth, australia
Re: Mills "Wizard" alloy corrosion removal
The seller told me the story about it, he found in the basement of a circa 1900 pub in the US, laying face down on the floor which explains that terrible water damage. The back door was long gone and I can see why, someone broke it open as wood is missing at the lock latching point in the top wood. The base is also gone so I imagine it was sitting upright for many years until that rotted and it fell face forward due to the weight. The mech doesn't seem to show much wear and as it dates 1926 this probably happened late 1920's. As for the mech before trying to remove anything I soaked every nut and bolt with penetrating oil for several hours . They nearly all came out easily with just a couple stubborn ones - but nothing broke thank goodness! I can't tell you how many hours I've spent hand making replacement collared bolts that need very close tolerances to allow parts to be locked in place but moveable. And there are quite a few used in this mech. On really well worn mechs of course those collars are often worn away allowing too much slop eventually, and the machine finally stops working.
- bryans fan
- Posts: 838
- Joined: Mon Feb 03, 2003 10:15 pm
- Reactions score: 12
- Location: Somerset
Who is online
Users browsing this forum: No registered users and 0 guests