Oh Dear...Broken Allwin Flick mech casing
Oh Dear...Broken Allwin Flick mech casing
Hello helpful people. I was hoping my first post would be a hello, but unfortunately it's turned into a "please help and advise me if you can" one.
I have a Ruffler and Walker "What's My Line" which generally works well, but today the casing holding the flick pin/bolt (not sure what to call it) has cracked and come apart. I've attached photos, I'm not sure whether to try super gluing it back together (I bet that's a daft idea) or well....I really honestly don't know what to do.
One pic shows the unit in its usual place, one taken out, and all the others the case and broken part.
Any help and advice would be gratefully received. Thanks, David
I have a Ruffler and Walker "What's My Line" which generally works well, but today the casing holding the flick pin/bolt (not sure what to call it) has cracked and come apart. I've attached photos, I'm not sure whether to try super gluing it back together (I bet that's a daft idea) or well....I really honestly don't know what to do.
One pic shows the unit in its usual place, one taken out, and all the others the case and broken part.
Any help and advice would be gratefully received. Thanks, David
Last edited by magikkk on Mon May 13, 2019 2:52 pm, edited 2 times in total.
Re: Oh Dear...Broken Allwin Flick mech casing
I have never seen this happen before, but does not surprise me as the damper takes constant thumping from the hammer, so over time I guess it could be a weak point... Good thing is this is hidden behind the cover, so any repair should be hidden, whether a weld job or brazing would do the job is worth a try.... Maybe with some added metal on the outside to provide support....
-
- Site Admin
- Posts: 6650
- Joined: Wed Nov 06, 2002 12:12 am
- Reaction score: 59
- Location: The Black Country
Re: Oh Dear...Broken Allwin Flick mech casing
I think a blob of weld on the inside might be favourite as a fail-safe solution.
Re: Oh Dear...Broken Allwin Flick mech casing
Thanks gents for the speedy replies.
Welding, I've never ever done that, is there anyone in the London area I could pay to do that quickly for me?
And just to be clear, we are saying "no" to epoxy glue (i.e arldite) for that?
Welding, I've never ever done that, is there anyone in the London area I could pay to do that quickly for me?
And just to be clear, we are saying "no" to epoxy glue (i.e arldite) for that?
-
- Site Admin
- Posts: 6650
- Joined: Wed Nov 06, 2002 12:12 am
- Reaction score: 59
- Location: The Black Country
Re: Oh Dear...Broken Allwin Flick mech casing
Because you've only got thin edges to glue and the detached part takes the full force of the hammer (cushioned only by the rubber stop), I doubt it would hold for more than a few plays. I've never welded either, but my friendly back-street garage welded steel tubing on a broken chicken hutch recently, and took payment in eggs!
Re: Oh Dear...Broken Allwin Flick mech casing
I'd suggest brazing or hard silver solder for this job over welding, because you can see into that hole and brazing done well will be invisible on both sides, while welding leaves a lumpier finish, and actually quite a delicate job to weld such a small thin part. A local proper bike shop should be well versed in brazing.
Re: Oh Dear...Broken Allwin Flick mech casing
Good advice.
Also, I now intend to pay for all purchases in Coventry with eggs...
Also, I now intend to pay for all purchases in Coventry with eggs...
Who is online
Users browsing this forum: No registered users and 88 guests